Braeburn 1025NC Instrukcja Użytkownika Pobierz pdf

This thermostat requires 24 Volt AC Power or two (2) properly installed

“AA” Alkaline batteries for proper operation. When connecting 24 Volt

AC Power the batteries may be installed as a backup.

For use only as described in this manual. Any other use

will void warranty.

1025NC

Single Stage Heat Only

Speciﬁcations

About Your Thermostat

Installation

System Testing

Setting User Options

Operating Your Thermostat

Thermostat Maintenance

Warning

Turn off power to the heating equipment

before installation.

Attention

For installation by experienced service

technicians only.

Read all instructions before proceeding.

This thermostat is compatible with:

  • Singlestageheatonlysystems

  • 250–750millivoltheatonlysystems

  • 2or3wirehydroniczonesystems

Electrical and control speciﬁcations:

 •ElectricalRating:24VoltAC

  •1ampmaximumloadperterminal

  •ACPower:18–30VoltsAC

  •DCPower:3.0VoltDC(2“AA”AlkalineBatteriesIncluded)

  •ControlRange:45°–90°F(7°–32°C)

  •TemperatureAccuracy:+/-1°F(+/-.5°C)

Terminations

  •1025NC–R,G,W1,V3,C

Speciﬁcations

1025NCW-100-03

Non-Programmable

Thermostat

Model number is located on back

of thermostat

Detailed

User Guide

1 2 3 4 5 6 ... 10 11

Podsumowanie treści

Strona 1 - User Guide

This thermostat requires 24 Volt AC Power or two (2) properly installed “AA” Alkaline batteries for proper operation. When connecting 24 Volt AC Power

Strona 2 - Single Stage Heat Only

1.Removethermostatbodybygentlypullingitfrombase.2.Removeoldbatteriesandreplacewithnewbatteries.3.Makesuretocorrectlypositi

Strona 3 - Provide Power

Strona 4 - Typical Wiring Conﬁgurations

2Single Stage Heat Only5 Setting User Options 6 Operating Your Thermostat7 Thermostat MaintenanceFor installation by experienced service technicians o

Strona 5

3Install your new Braeburn thermostat in 5 basic steps:1 InstalltheSub-Base2 ProvidePower3 ConnectYourWires4 SetInstallerSwitches5 Attach

Strona 6 - installer switches

4Terminal Function Description R   Input PowerConnection(24VoltACHeating       TransformerorMillivoltPowerSource) G  

Strona 7 - Setting User Options

5NOTES - Conventional Systems[1]Fora2-wirezonevalveyouwillnotconnectV3[2]Ifbatteriesareinstalled,the24VoltACcommonconnectionisop

Strona 8 - Operating Your Thermostat

Factory Setting Switch Default Options Comments6 F/C F HE/HG HG Set Installer Switches4 F Selectforfahrenheittemperaturesc

Strona 9 - Thermostat Maintenance

74System TestingWarningRead Before Testing• Donotshort(orjumper)acrossterminalsonthegasvalveoratthe systemcontrolboardtotestthe

Strona 10 - Limited Warranty

8 User Factory Setting No. Options Default Options Comments  1 1ststage0.5 0.5, 1.0 Selecta1ststagetemperature   differ

Strona 11

9Detailed Explanation of User Options: Temperature DifferentialThedifferentialsettingisthetemperaturecontrolrangethatyourthermostatwillpro